Placement Papers: Brakes India Limited 2007
Download PDF of This Page (Size: 134K) ↧
Examrace Placement Series prepares you for the toughest placement exams to top companies.
Stage I
TEST I: GENERAL APTITUDE: 15 MINS: 25 QUESTIONS
IN THE BELOW QUESTIONS BLOCKED WORDS WERE ANSWERS
Commerce minister of India, ____ (Arun jaitley)
First car using CRDI is____ (hyundai Accent, Skoda Octavia,)
First Indigenous car sold in European market____ (tata indica, M&M scorpio, fiat palio)
Selection Committee Leader of Indian cricket team____ (kiran more, syed kirmani, brijesh patel)
Governor of RBI (Reserve Bank of India) ____ (s. Rangarajan, sivathanu pillai, y. v. Reddy, bimal jalan)
WTO meeting recently held at____ (Cancun, Jakarta, Geneva)
Economic Growth Rate is measured by____ (GDP, inflation, GNP)
HAL's (Hindustan Aeronautical Limited) indigenous aircraft____ (Tejas, trishul, danush)
Which European country does not have the same currency____ (U. K, spain, france, germany)
Meaning of URGE____ (desire, strength, forceful demand)
Opposite of PHENOMENAL____ (ordinary)
Find in which part Grammatical/idiomatic error occurs in the sentence
Yesterday while/crossing the road/he was/run out by a lorry
A B C D
-
ISRO chairman____ (madhavan nair)
-
opposite of obscure (explicit)
-
Meaning of apprehend (fear)
-
what is the name of the robot presented by japan to Indonesia-azimo Honda
-
it is very cold outside. You must take some clothes with you. Ans: Combined sentence will start with As it is very cold outside:
-
By the time we reached the station the train had departed (ans).
Stage II
TEST II: TECHNICAL TEST: 30 min: 75 QUESTIONS
-
In V belt drive contact is made on
-
bottom
-
sides
-
bottom and sides
-
-
Section modulus of hollow shaft PI/32 * (D4 − d4)/D
-
Down milling is also called Climb milling
-
Drilling is an example of Oblique cutting
-
Section view of ‘C’ washer
-
Deflection of simple supported beam carrying UDL 5/384 * Wl4/EI
-
Flexible coupling is used because
-
Washer is used to provide bearing area
-
Initial tension is considered in
-
tension springs
-
Compression springs
-
Both
-
-
Kelvin plank law deals with
-
Conservation of work into heat
-
conservation of heat into work
-
-
Soldering alloy consists of Tin and lead
-
Why chromium is used in steel alloys? Corrosive resistance
-
High cutting speed is obtained while machining
-
HSS
-
carbide
-
CBN
-
-
Metal forming is an example of chipless machining
-
Top rake angle is provided for Easy removal of chip
-
Alloying is done for increased strength and application
-
Transformer is used welding
-
to convert AC to AC
-
AC to DC
-
DC to AC
-
-
spheroidal cast iron is getting from Grey cast iron by adding Mg
-
In throttling process Enthalpy constant
-
70 cc of engine means swept volume
-
Tan (a) = co efficient of friction
-
Geneva mechanism is used for Intermittent motion
-
In NC system for profile machining
-
point to point
-
contour motion
-
paraxial m
-
-
In centreless grinding, the grinding wheel and the regulating wheels rotate in the same direction.
-
Centridal distance of a semi circle 4 * r/3 * pi
-
Highest packing factor: FCC
-
Which chart takes care of conrol attributes: Pchart, C chart, R chart
-
Fixture is used for holding the workpiece without disturbing the tool path
-
Code for circular interpolation G 02
-
Order of transmission in a car: EFCPD Engine Flywheel Clutch propeller shaft Differential
-
Reverse gear has less speed because
-
More speed is not necessary in reverse gear
-
Steering is difficult in the reverse direction
-
less space availability
-
Design simplification
-
-
which of the following has no unit: Specific gravity
-
use of annealing: To relieve stresses
-
question on stress concentration 4 figures: One with the notch is the answer
-
how many squares are there in this figure: 14
-
pulley question: w = f/2
-
equivalent stiffness of springs in series: k1k2/(k1 + k2)
-
Deflection = 5 mm. Stiffness = k, Then applied load is 5 k 39 bevel gear is used in differential
Diagram Questions (Technical) 20 Questions Like
what is the stress in xx section?
-
bending
-
axial loading
-
both General Aptitude questions like
-
What is the no of straight lines in this diagram
-
Find NO of Triangles
-
1st 20 questions: Diagrammatic questions from SOM, E-MECH, DESIGN, ENGG DRAWING
Stage III
GROUP DISCUSSION:
Quality will improve marketing of a product.
Elimination round. Those who have dominated were shortlisted. Same topic for all the groups. 12 out of 25 were shortlisted.
Stage IV
Interview Questions:
TECH INTERVIEW 1: MANUFACTURING: 20 − 30 MINS
TECH INTERVIEW 2: DESIGN: 20 − 30 MINS
HR INTERVIEW: 15 MINS
NO ELIMINATION AT THE END OF EACH INTERVIEW CUMMULATIVE____
Questions on field of interest
- stress-strain diagram
- Heat treatment All processes
- Types of springs
- What is spring constant
- What is Pascal's Law?
- Bernoulli's theorem and it's application
- Newton's three laws of motion
- Reynolds no? where is it used? Can it be used in brakes?
- Boyle's law, charles law
- In a balloon, both pressure and volume varies when u blow it. How will u apply boyle's law in this situation?
- favourite subject in + 2 (physics)
- focal Length, unit of power of lens (dioptre)
- Types of protective coating
- specific gravity? Unit?
- what is 1 micron?
- screw guage and vernier caliper
- what r the CAD software u know?
- Given a component, asked the material and the manufacturing process
- HR Questions:
- what is ur caste?
- family details
- who inspired u to study?
- achievements
- smoking? drinking?
- Personality traits