Placement Papers: Bosch 14th Nov 2006

Get unlimited access to the best preparation resource for competitive exams : get questions, notes, tests, video lectures and more- for all subjects of your exam.

TOTAL DURATION OF TEST IS 90 min & NEGETIVE MARKING IS THERE.

SECTION 1.

Total 50 questions correct Answer + 2 marks, wrong answer-1 mark.

Out of 50 ques. 40 from engineering and 10 from aptitude.

SECTION 2.

Total 25 questions on English.

Paper is as follows.

SECTION 1:

  1. Two force acting along the same line but in the opposite directions. They r called
    1. Concurrent
    2. coplanar
    3. collinear
    4. non concurrent
  2. Two basic systems of forces
    1. Coplanar, concurrent
    2. non concurrent, concurrent
    3. Coplanar, non coplanar
    4. concurrent, non coplanar
  3. Formula for power in HP
  4. Forces lying in the same plane but never met
  5. Ger ratio for helical gears one of 30 tooth and the other 60 tooth
    1. 800: 1
    2. 2: 1
  6. Four rectangle strips of size 10 X 1 inch r placed on a table as shown in the figure. What is the area covered on the table.
    1. 36
    2. 40
    3. 1600
    4. 80
  7. If u traveled 45 min at 4 miles per hr and 30 min at 3 miles per hr. What is the distance covered by u in 1 hr and 15 min.
    1. 8 miles
    2. 6 miles
    3. 7miles
    4. 10
  8. A ball of weight 10N is dropped freely from rest at a height of 4 mts. What is its total mechanical energy after it has traveled 1 meter.
  9. Two bodies of same mass r traveling at a velocity of 2 m/sec in opposite direction. After collision one travelled with 1.8 m/sec what abt the other.
    1. equal to 1.8 m/sec
    2. more than 1.8
    3. Less then 1.8
    4. can not say
  10. If X-component of a force is Ve and Y-component is + Ve, in which plane the Resultant would be (a) check it
    1. First quadrant
    2. second
    3. third
    4. fourth
  11. A body is said 2 b in equilibrium
    1. if it is in rest
    2. if it is I uniform velocity
    3. if the sum of the forces acting on it is zero
    4. none
  12. X15 βˆ’ X13 + X11 βˆ’ X9 + X7 βˆ’ X5 + X3 βˆ’ X = 7 than value of X16?
  13. a chain of leanth 1 mt and mass 1 kg is placed on a table. What leanth of the chain must be hanged freely from the table so that is will drag the remaining chein freely
  14. Main purpose of governer
    1. to live happy life
    2. to increase engine speed
    3. to decrease engine speed
    4. to run engine smoothly
  15. A steel beam of mass m and length l is placed on a surface. a couple u is applied at the ends to rotate the beam at 90 0. What is the work done.
  16. A & B r two weight lifters. A can lift 100 pounds 10 times a minute, where as b lifts 100 pounds 10 times a sec. Who is doing more power and work.
    1. A&B
    2. A omly
    3. B only
    4. none.
  17. A ship is 77 Km away from the shore. It had a leak due to ehich water is flowing into the ship@1 ton/min. A pump is used to pump the water out of the ship@30 ton/hr The ship sinks if the water Qty reaches 210 ton. What should b the speed of the ship to reach the shore b4 it sinks.
    1. 7 mph
    2. 11mph
    3. 15
    4. 20
  18. Very simple. Que. Find the hypotenuse?
    1. Sides 8,11, find hyp
    2. a similar one. To find side.
  19. Which is the largest side in a right angled triangle
    1. hypotenuse
    2. edgescent side
    3. opposite side
  20. The angle of depression from the top a building to another building is 120. The distance b/n the two is 50 mts. What is the difference in the height of buildings.
    1. 10.6
    2. 20.3
    3. 10.4
    4. 48.9
  21. Simplyfy [3v________27 βˆ’ v () ] 2
  22. Belt drives r mainly used for
  23. BS thread profile has
    1. 0
    2. 450
    3. 250
    4. 90 0
  24. The main purpose of bearings
  25. When compared to spur gears bevel gears r more.
    1. noisy
    2. smooth
  26. The angle b/n bore axis of gear and the tangent to the teeth profile is called
    1. PA
    2. helix
  27. The circle touching the outer edge of the teeth is called
    1. Base circle.
    2. pitch crcl
    3. addendum crcl
    4. ?
  28. The area of the piston A is 10 cm2 and that of B is 4 cm 2. If 10n load is applied on the piston A what is the force on the piston B.
    1. 100N
    2. 40N
    3. 10N
    4. none
  29. The force exerted by a spring depends on
    1. Material of the spring
    2. Design of the spring
    3. Length of the spring
    4. all
  30. If a body is isolate from it՚s mating parts and all forces acting on it r shown then it is called.
    1. BM diagram
    2. SF diagram
    3. free body diagram
    4. none
  31. A coin and a ring of same mass and diameter r allowed to roll smoothly from the top of a inclined plane. Which one reaches the bottom first.
    1. coin
    2. ring
    3. both reaches same time
    4. none
  32. A ball is thrown horizontally. After hitting the ground it again raises with some velocity. This is bcoz.
  33. a problem on balancing masses.
  34. a mass is rotating. With rad/sec. Simple problem on basics.

35 given 0

36 to 50 sorry. i forgot.

Developed by: